Problem Description:
Primer Shutdown Error.
Corrective Action:
Try the following:
1. Check that the Service Station Cable (the grey flat cable with the grey connector) is plugged into the Main PCA, and that the clips of the connector are closed. Also check that the cable is not damaged.
2. Replace the Service Station.
Problem Description:
This firmware error code is related to the detection of the Printhead cleaners by the line sensor. It always happens during initialization, while checking the Printhead Cleaners. In most case, it is a problem of incorrectly inserted Printhead Cleaners, but it can also be caused by an incorrectly assembled Service Station.
Corrective Action:
Try the following:
1. Remove the Printhead Cleaners and reinsert them again.
2. If the error still persists, perform the Service Station Calibration.
3. If the error still persists, an onsite visit is necessary to repeat the calibration or to change the Service Station assembly or the Carriage Assembly.
Problem Description:
Unable to detect Fan (X = 7 – Vacuum, 8 – Cooling, 9 – Aerosol).
Corrective Action:
Try the following:
1. Make sure that the Fan is connected correctly to the Main PCA.
2. Turn the Printer OFF and disconnect the Fan from the Main PCA. Connect a New Fan to the Main PCA and power ON the Printer. If the New Fan functions correctly without any Error Codes then remove the Old Fan from the Printer and install the New one.
3. If the New Fan does not function correctly either, then replace the Main PCA.
Problem Description:
The Trailing Cable has been incorrectly connected.
Corrective Action:
Try the following:
1. Power the Printer OFF disconnect the Trailing Cable. Replace the Trailing Cable if the ends are not flat or are damaged. Reconnect the Trailing Cable correctly, making sure it is pushed in firmly. Power ON the Printer and check if the Error Code has disappeared.
2. If the Error Code continues, replace the Main PCA taking care when connecting the Trailing Cable.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Faulty APS. Replace the APS.
3. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Faulty APS. Replace the APS.
3. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
ADC0 Internal channels check Failure.
Corrective Action:
Replace the Main PCA.
Problem Description:
Bad IDS pressure read.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Check that the Air Pressurization System Sensor Cable is correctly connected and is NOT damaged.
3. Check all the tubes of the APS and make sure they are NOT pinched or damaged.
4. Faulty APS. Replace the APS.
5. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Bad Humidity Read
Corrective Action:
Try the following:
1. Replace the ISS PCA.
2. Replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Bad Ambient Temperature measured.
Corrective Action:
Try the following:
1. Make sure that the Ambient temperature is within the allowed range (between 0 and 55 Degrees Centigrade).
2. Replace the Main PCA.
