Problem Description:
The Backup EEROM contents stored in the Hard Disk Drive are not
consistent with the ones required by the firmware.
Corrective Action:
Try the following:
1. Perform Backup EEROM and ALL calibrations. Perform EEROM Setup to reconfigure the Printer.
Problem Description:
The Printer has detected a leak in the Tubes System – Should ONLY appear in printers with the Ink Leak Detector installed.
Corrective Action:
Try the following:
1. Check for ink in the Ink Leak Detector and, if present, replace the complete Tubes System.
2. The Ink Leak Detector could have been triggered due to condensation in the Printer. Power OFF the Printer and allow the Printer to dry for 15 minutes. Power ON and check if the System Error Code has disappeared.
3. Replace the ISS PCA
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
The Printer has detected a leak in the Tubes System – Should ONLY appear in printers with the Ink Leak Detector installed.
Corrective Action:
Try the following:
1. Check for ink in the Ink Leak Detector and, if present, replace the complete Tubes System.
2. The Ink Leak Detector could have been triggered due to condensation in the Printer. Power OFF the Printer and allow the Printer to dry for 15 minutes. Power ON and check if the System Error Code has disappeared.
3. Replace the ISS PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.
2. Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged.
3. Replace ONE Ink Cartridge at a time, checking if the System Error Code disappears.
4. Faulty APS. Replace the complete APS.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Problem in Depressurizing Air System.
Corrective Action:
Try the following:
1. Check the APS for any signs of Ink. Also inspect ALL Ink Cartridges for any signs of leaking (the bottom valve of the Ink Cartridge will contain ink).
2. If there is ink leakage, replace ALL Ink Cartridges, the APS and the Tubes System.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Error in Calibrating the APS Sensor.
Corrective Action:
Try the following:
1. Check the APS Sensor and the valve cables, making sure that they are NOT damaged and connected correctly.
2. Replace the APS or the ISS PCA.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.
2. Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged.
3. Check that the Air Tube from the APS is correctly connected to the Tubes System.
4. Replace ONE Ink Cartridge at a time, checking if the System Error Code disappears.
5. Faulty APS. Replace the APS.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.
2. Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged.
3. Check that the Air Tube from the APS is correctly connected to the Tubes System.
4. Replace ONE Ink Cartridge at a time, checking if the System Error Code disappears.
5. Faulty APS. Replace the APS.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Line Sensor not connected correctly
Corrective Action:
Try the following:
1. Check/reconnect the Line Sensor.
2. Replace the Line Sensor.
3. Replace the Carriage Assembly.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Bad Line Sensor.
Corrective Action:
Try the following:
1. Replace the Line Sensor.
2. Replace the Carriage Assembly.
3. Replace the Trailing Cable.
4.Replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
