HP DesignJet T1100

Error Code 98:YZ

Posted by on July 15, 2013 at 4:12 pm

Problem Description: Automatic backup print mode enabled. Corrective Action: Try the following: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. 2. Recover the printheads.

Error Code 94.1:YZ

Posted by on July 15, 2013 at 4:08 pm

Problem Description: Profiling algorithm failed. Corrective Action: Try the following: 1. Profiling failed due to a different error (not algorithm / data processing). 2. Perform the Line Sensor calibration. 3. See Troubleshooting, Line Sensor. 4. If the System Error continues, replace the Line Sensor. 5. If the System Error continues, replace the Carriage PCA. 6. [...]

Error Code 94:YZ

Posted by on July 15, 2013 at 4:04 pm

Problem Description: Color calibration Error. Corrective Action: Try the following: 1. Profiling failed due to a different error (not algorithm / data processing). 2. Perform the Line Sensor calibration. See Troubleshooting, Line Sensor 3. If the System Error continues, replace the Line Sensor. 4. If the System Error continues, replace the Carriage PCA. 5. If [...]

Error Code 93:YZ

Posted by on July 15, 2013 at 3:59 pm

Problem Description: Unable to pressurize the Ink Delivery System. Corrective Action: Try the following: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. 2. Perform the Ink Delivery System diagnostic test to further troubleshoot the problem. 3 If the [...]

Error Code 87:YZ

Posted by on July 15, 2013 at 3:58 pm

Problem Description: Problem finding the Scan-axis encoder reading. Corrective Action: Try the following: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. 2. Movement jam. 3. Possible paper jam. 4. Mechanical Initiator scan axis measure error. 5. Check that [...]

Error Code 86:YZ

Posted by on July 15, 2013 at 3:53 pm

Problem Description: Possible Paper Jam. Corrective Action: Try the following: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. 2. Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is [...]

Error Code 85:YZ

Posted by on July 15, 2013 at 3:49 pm

Problem Description: Problem finding the Drive Roller zero. Corrective Action: Try the following: 1. Perform the Media Drive diagnostic test to troubleshoot the problem further. 2. If the System Error continues, replace the Encoder Disk and Encoder Sensor.

Error Code 84:YZ

Posted by on July 15, 2013 at 3:45 pm

Problem Description: Back tension servo shutdown (roll feeding). Corrective Action: Try the following: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. 2. If the problem persists, contact HP support.

Error Code 81.1:YZ

Posted by on July 15, 2013 at 3:42 pm

Problem Description: Problem finding the Drive Roller zero. Corrective Action: Try the following: 1. Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. 2. Perform [...]

Error Code 81:YZ

Posted by on July 15, 2013 at 3:36 pm

Problem Description: Problem with paper advance. Corrective Action: Try the following: 1. Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. 2. Perform the Media [...]