Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Faulty APS. Replace the APS.
3. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Faulty APS. Replace the APS.
3. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
ADC0 Internal channels check Failure.
Corrective Action:
Replace the Main PCA.
Problem Description:
Bad IDS pressure read.
Corrective Action:
Try the following:
1. Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected.
2. Check that the Air Pressurization System Sensor Cable is correctly connected and is NOT damaged.
3. Check all the tubes of the APS and make sure they are NOT pinched or damaged.
4. Faulty APS. Replace the APS.
5. If the error code continues, replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Bad Humidity Read
Corrective Action:
Try the following:
1. Replace the ISS PCA.
2. Replace the Main PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
Bad Ambient Temperature measured.
Corrective Action:
Try the following:
1. Make sure that the Ambient temperature is within the allowed range (between 0 and 55 Degrees Centigrade).
2. Replace the Main PCA.
Problem Description:
The Backup EEROM contents stored in the Hard Disk Drive are not consistent with the ones required by the firmware.
Corrective Action:
Try the following:
1. Perform Backup EEROM and ALL calibrations. Perform EEROM Setup to reconfigure the Printer.
Problem Description:
The Printer has detected a leak in the Tubes System – Should ONLY appear in printers with the Ink Leak Detector installed.
Corrective Action:
Try the following:
1. Check for ink in the Ink Leak Detector and, if present, replace the complete Tubes System.
2. The Ink Leak Detector could have been triggered due to condensation in the Printer. Power OFF the Printer and allow the Printer to dry for 15 minutes. Power ON and check if the System Error Code has disappeared.
3. Replace the ISS PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
The Printer has detected a leak in the Tubes System – Should ONLY appear in printers with the Ink Leak Detector installed.
Corrective Action:
Try the following:
1. Check for ink in the Ink Leak Detector and, if present, replace the complete Tubes System.
2. The Ink Leak Detector could have been triggered due to condensation in the Printer. Power OFF the Printer and allow the Printer to dry for 15 minutes. Power ON and check if the System Error Code has disappeared.
3. Replace the ISS PCA.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Problem Description:
APS Failure.
Corrective Action:
Try the following:
1. Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.
2. Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged.
3. Replace ONE Ink Cartridge at a time, checking if the System Error Code disappears.
4. Faulty APS. Replace the complete APS.
Warning:
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
